Suzuki Swift, Baleno & Toyota Starlet K15B Water Pump - MAP-101021

Vehicle Fitment & Part Details

Water pump for the current-generation Suzuki Swift IV (FZ/NZ) 1.4 K14B petrol — mechanical, for V-ribbed belt drive, 6-vane impeller, 59.6mm impeller diameter, supplied without gasket (sealant required on fitment). Covers the full Suzuki K-series K10 / K12 / K14 / K15 petrol engine range across the Swift IV / V, Baleno, Dzire, Ertiga, Ciaz, Ignis III, Jimny, Splash, Alto VII, Celerio, SX4 S-Cross, Vitara, S-Presso, and Fronx — plus the Toyota-rebadged SA-market models Starlet, Urban Cruiser, and Rumion. Confirm compatibility by matching the listed fitment details and VIN/engine information where variants exist.

Key Details

SKU

MAP-101021

Component

Water Pump

Generation

NEW / current-generation Suzuki models (2008 onwards) with K-series engines only — plus Toyota rebadges (Starlet, Urban Cruiser, Rumion). NOT for older G-series Suzukis.

Primary Fitment

Suzuki Swift IV (FZ, NZ) 1.4 K14B 70kW (02/2011-)

Specs

Mechanical, V-ribbed belt drive, 6-vane impeller, 59.6mm impeller diameter

Key Benefits

• Covers the full Suzuki K-series K10 / K12 / K14 / K15 petrol engine range — a single water pump for most current Suzukis sold in SA
• Also fits the SA-market Toyota-rebadged Suzuki platforms: Starlet (1.4 K14B / 1.5 K15B), Urban Cruiser (1.5 K15B), and Rumion (1.5 K15B)
• Mechanical drive for V-ribbed accessory belt, 6-vane impeller, 59.6mm impeller diameter

Product Specifications

Vehicle Fitment — NEW K-Series Models Only

This listing covers the current-generation Suzuki models (2008 onwards) with K-series engines, plus Toyota-rebadged versions. It does NOT fit older G-series Suzukis.

Includes 45 supplied applications.

Fitment Notes

• Generation check first: Engine code must start with "K" (K10B, K10C, K10C-T, K12B, K12C, K12D, K12M, K14B, K14C, K14D, K15B). If the engine code starts with "G" (e.g. G13BB, G16B), this is the wrong pump — see the older G-series water pump listing.
• The Toyota Starlet, Urban Cruiser, and Rumion are Maruti Suzuki-built rebadges sold in SA — Starlet is a rebadged Baleno, Urban Cruiser is a rebadged Vitara Brezza, Rumion is a rebadged Ertiga. They use the same K14B or K15B engine as the equivalent Suzuki.
• Supplied without gasket or seal — use sealant on fitment as specified by the manufacturer.
• Always match the engine code and VIN before ordering. Verify the physical dimensions of your removed pump (6-vane impeller, 59.6mm impeller diameter, V-ribbed belt drive).
• South African market filtered: LPG dual-fuel variants have been excluded from the supplied feed as non-SA market.

Installation / Use / Maintenance Tips

• Drain the cooling system fully and catch coolant in a clean container if it is to be reused — or dispose of it according to local regulations if contaminated.
• Supplied without gasket — apply the correct sealant (manufacturer-specified, usually a silicone-based high-temperature sealant for cooling system use) evenly to the pump mating surface before fitting.
• Clean both mating surfaces (pump and block/timing cover) thoroughly before fitting. Do not use an abrasive pad that will leave grit in the cooling passages.
• Tighten the mounting bolts evenly in a cross pattern to the manufacturer's torque specification; over-torquing will distort the pump housing and cause leaks.
• Inspect the V-ribbed accessory belt and tensioner at the same time — a worn belt or tensioner will shorten the new pump's life. Replace the timing chain / belt service items per the manufacturer's service schedule.
• Refill with the correct Suzuki-spec coolant, bleed the cooling system fully, and run the engine up to operating temperature while checking for leaks and confirming correct thermostat and fan operation.

Common Questions

Does this fit my Toyota Starlet, Urban Cruiser or Rumion?
Yes — these are Maruti Suzuki-built Toyota rebadges. The Toyota Starlet uses the K14B (2020-2022 models) or K15B (2022 onwards), the Urban Cruiser and Rumion use the K15B. This water pump fits all of them.

Does this fit the old Suzuki Baleno, Swift, or Alto?
No. The old Suzuki Baleno (1995-2002), Swift I / II (1984-2005), and Alto IV / V (1994-2002) all use G-series engines (G10, G13, G16) and need a different water pump. See the separate older water pump listing.

How do I know if my engine is K-series or G-series?
Check the engine code stamped on the engine block or the VIN plate. K-series codes start with "K" (K10B, K12B, K14B, K15B, etc.). G-series codes start with "G" (G13BB, G16B, etc.). If it starts with "K", this is the correct pump.

Is a gasket included?
No — this pump is supplied without a gasket or seal. Use a manufacturer-approved cooling-system sealant on fitment.

Does this fit hybrid / SHVS / Mild Hybrid variants?
Yes — the hybrid variants (K12C SHVS, K12D Mild Hybrid, K14D Sport SHVS) use the same water pump as the non-hybrid K-series engines of the same capacity.

How do I confirm fitment if there are multiple variants?
Use VIN, engine code (must start with K), and the physical dimensions of the removed pump (6-vane impeller, 59.6mm impeller diameter, V-ribbed belt drive) and compare them to the fitment and specifications sections above. If unsure, request fitment assistance before ordering.